[SOLVED] Displayotron Hat IOerror[Errno 5]
your kernel is a bit oldish but I don't suspect that'd be a problem... how did you install the dothat lib?
View ArticleIs my LCD board bust?
Fixed! :) Thanks. I received the replacement 8" screen kit and my PiCade is now working a treat! :) I only had to swap over the control board. As I did not have to use the display panel I'll put it...
View ArticleRaspberry pi 2 blank TV and two lights
yeah, USB cables often cause some misery... I like the convenience of flat cables, but it's a no-go for my Pi2 but for example OK for headless A+.
View ArticlePhat DAC install
Thanks for the indication of the used pins! These are nearly the same as the HifiBerry DAC+. Makes sense, since they use nearly the same hardware.
View ArticleProblem when using Jessie
I get the following error when I try to run any game. runcommand.sh /dev/tty no such device or address I've made sure the user pi is in the group tty. I have installed retro pie from scratch on the...
View Article[SOLVED] Displayotron Hat IOerror[Errno 5]
I used this command:curl get.pimoroni.com/dot3k | bashand I get the following...
View ArticleTrouble Programming New Picade Key Mapping
Okay I will try the update script. I take it I run that on the Pi? This hex file? "C:\Users\Bob\AppData\Local\Temp\58e9973bb6e2e908c6c199f5a9d39075.tmp\output/Picade-NES.ino.hex"
View ArticleProblem when using Jessie
Use Wheezy - RetroPie does not fully support Jessie yet (We are still testing/finalising it) github.com RetroPie/RetroPie-Setup/blob/master/README.md RetroPie-Setup ============== General Usage...
View Article[SOLVED] Displayotron Hat IOerror[Errno 5]
What happens if you: i2cdetect -y 1 What Raspberry Pi is it btw?
View Article[SOLVED] Displayotron Hat IOerror[Errno 5]
The Raspberry Pi is Model B+ V1.2Result of i2cdetect -y 1 pi@Caligula ~/Pimoroni/dot3k/dothat/basic $ sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10:...
View ArticleNeed to cancel the order
Hi! I'm afraid that order has already shipped. If you return it to us unopened then we can cancel and refund the order!
View ArticleTechnical Support
Hello,Just to be sure.I have an question about the zumo chassis, does the Micro metal gearmotor (extended back shaft) COM0801 298:1 fitin place?Best regards, Ton
View ArticleProblem when using Jessie
Your actual problem looks due to missing /dev/tty what is the output of ls -l /dev/tty Are you running this from the terminal on the RPI. How did you install ? Did you start from the minimal Jessie...
View ArticleZumo chassis
Hello,Just to be sure.I have an question about the zumo chassis, does the Micro metal gearmotor (extended back shaft) COM0801 298:1 fitin place?Best regards, Ton
View ArticleClik here to view.
Side Art
Just wanted to show my build, I made the side art on "pages",and is printed onto vinyl sticker paper, quite pleased with the result, I am looking to install lighting at a later date....
View ArticleScroll pHAt Not working at all
I soldered the GPIO header on to the raspberry pi and installed the requirements using the script given on github but my scroll pHAt will not light up at all, I have tried tyding up the soldering on...
View ArticleScroll pHAt Not working at all
Yes, you must solder that header onto the Scroll pHAT :-)
View ArticleSide Art
That is really cute! If you want to write up how you did it we'd love to put it on the Pimoroni Learning Portal!
View Article