Do Headphones cause damage to PHAT DAC?
OK, I bought 2 PHAT DAC's. I soldered the headers on and plugged one onto my PI3 with the Official Foundation display attached. I burned a Raspian 5.27.16 image onto my 32GB card and put it in the pi....
View ArticleClik here to view.
3D Printing Show & Tell
Had this in the back of my mind for ages: IMG_20160711_182210.jpg2822x2117 996 KB IMG_20160711_182842.jpg4032x3024 2.41 MB IMG_20160711_184158.jpg2822x2117 795 KB IMG_20160711_184550.jpg2822x2117 550...
View ArticleDo Headphones cause damage to PHAT DAC?
omxlayer does not support ALSA, so you won't be able to route audio to the pHAT DAC (or any other source but the integrated card for that matter). there are plenty of alternatives that will work for...
View ArticleUnicorn-Hat | Raspberry Pi 3 | No Output
I shall try that tonight and get back you. Thank you.
View Article3D Printing Show & Tell
Unfortunately it was a fresh Pi so I only had the demos that came with the library. I left rainbows.py running for a good while at what I guess was a brightness of 1.0 - tho it's not specified in the...
View Article3D Printing Show & Tell
I believe the default is half the max these puppies can blast, a hard limit set in the library for a few months now. That's not to say you shouldn't tone down the show, but rainbow.py has brightness...
View Article3D Printing Show & Tell
I think I pulled it down fairly recently - I'll check this evening.
View ArticleEnviro pHAT installation error
Good afternoon, After confirmation from Sandy a wider audience is perhaps needed for this one. Any guidance is appreciated. Thanks Background, it's a fresh install of Jessie, updated as of today on a...
View ArticleEnviro pHAT installation error
I suspected that you'd be the one who could help Pete out, @RogueM!
View ArticleEnviro pHAT installation error
that sounds very much like a temporary glitch with the PyPi repo. ... you should be able to use python 2 in the interim, though I suspect none of the examples were copied, so I'd try again in an hour...
View ArticleEnviro pHAT installation error
Hi @RogueM, thanks for the reply. I'll try again later on. i copied down the repo's and the 3 examples do work so it seems so far it's all working. I also did the same for the blinkt install, though...
View ArticleEnviro pHAT installation error
yes, not happening here right now, but it could very well be location dependent... I've had that sort of problems myself before, unfortunately it's out of our control :(
View ArticleEnviro pHAT installation error
No worries, thanks for having a gander and hopefully it is just down to 3rd party problems. Will try again, if and when it works i'll post my findings. Cheers.
View ArticleEnviro pHAT installation error
PyPi seems to be having a bad day, I keep getting server errors when I push new packages, and the website takes an age to load.
View Article3D Printing Show & Tell
On closer inspection of my version (2.1.0) of the UnicornHAT library, it definitely has the 50% brightness limitation in "brightness" but "rainbow.py" has no explicit brightness setting. I assume...
View Article3D Printing Show & Tell
I know @gadgetoid has also inserted a warning if brightness is set too low, not sure what level. If you think some of the examples don't work properly then try them with a slightly higher value and...
View Article3D Printing Show & Tell
The examples work fine with them all being set to 0.4, it's just the code warns you when you set brightness to anything less than ~0.23, but the comment for the function recommends a value of 0.2. I...
View ArticleWhen is flotilla available for buying
I was going to ask again because I want to buy another Kit. Anyone from Pimorini that would like to answer when will we be able o buy extra Flotilla Kits? Greetings,Rod
View Article
