7" touchscreen rpi 2
Could you post a photo of your setup. Also is the text on the cable between the Pi and the display driver board showing on the inside, or the outside of the loop? Don't ask me why this matters, but it...
View ArticleClik here to view.
7" touchscreen rpi 2
Pictures as requested. I have tried reversing the dsi cable to no and had no luck. The system is being powered from a 2a supply into the display board and linked up to the pi (which as powers and...
View Article7" touchscreen rpi 2
Any way you cab double check the PI is actually booting? I've seen a few instances of cards becoming corrupted after updating, and had a dodgy one myself. Worth a check! Did you try the DSI cable with...
View Article7" touchscreen rpi 2
That's quite all-right... Was hoping someone would be able to do that. I can SSH to the pi, and if I disconnect the dsi cable and plug in a hdmi display it works (needs a reboot). I have tried the dsi...
View ArticleNo sound Piano Hat
No Sound after install of your script everything looked like it went ok the leds come on when the keys are touched but no sound I do get a comment after I sent the command for the simple piano like...
View ArticleNo sound Piano Hat
How are you trying to run the simple-piano.py example file? Might be that you're not in the right directory for the example to pick up the sounds folder: cd ~/Pimoroni/pianohat python simple-piano.py
View Article7” Touch Screen - rotate screen issue
Hi I have problem to rotate screen on my new 7” Touch Screen with original stand. I have updated system according to instruction and also added lcd_rotate=2 line to /boot/config.txt. but the screen is...
View Article7” Touch Screen - rotate screen issue
That should do the trick. Could you post the contents of your /boot/config.txt, use triple backticks to format it as code ```text like so ``` You're also running Raspbian?
View ArticleClik here to view.
Attaching the 12.1" screen
Before I come up with a solution (Maybe using some tape to secure the back of the screen), I wanted to illustrate the problem I have. Due to the size of the 12.1" screen, even when the nuts are just...
View ArticleAttaching the 12.1" screen
Also - how are the plastic feet/pads supposed to attach to the driver board ? Am I supposed to tie the board to them ? Would have been easier with some that go through the holes in the driver board...
View ArticleAttaching the 12.1" screen
It's definitely not a friction fit, the feet do all the work of holding the screen in place. The bolts on the corners shouldn't be tightened to the point that the whole assembly bends. If you loosen...
View ArticleAttaching the 12.1" screen
Thanks - Due to the raised border/edge of 12.1, even with it attached without tightening the nuts, it has a gap making the black pads less useful.
View ArticleClik here to view.
Attaching the 12.1" screen
The pads look like this.. Square top, with hollow section underneath, hence I assumed the controller board is supposed to be tied to them ? Sorry for image quality/contrast
View ArticleClik here to view.
Attaching the 12.1" screen
Here's another couple of photos - the X is in contact with the black edge of the screen, which is raised, so it cannot lay flat against the back of the screen. screen3.jpg1280x720 293 KB...
View ArticleClik here to view.
7” Touch Screen - rotate screen issue
Please find attached my config.txt file. I have SD card with NOOBS config.jpg1920x1080 158 KB
View Article7” Touch Screen - rotate screen issue
Bizarre. I can't see anything untoward. My best guess is that you're not quite updated. What does it say if you fire up a terminal and run this?: uname -a I'd suggest running this again to see what...
View Article7” Touch Screen - rotate screen issue
it shows this Linux raspberrypi 4.1.7-v7+ #817 SMP PREEMPT Sat Sep 19 15:32:00 BST 2015 armv7l GNU/Linux I have updated according to yours instructions and still the same under uname -a
View ArticleAttaching the 12.1" screen
I have sorted it now anyway, by increasing the depth of the black feet, with some other rubber feet. I googled the pads, and they are def for cable ties, so if there were supposed to be pads for...
View ArticleNo sound Piano Hat ( fixed)
Hello and Thanks it is now working I went to Pimoroni/pianohat$ sudo pythonsimple-piano.py and it worked like a dream so why don't this command work for me sudo python...
View ArticleMy 12.1" screen experience
I have the 12.1" screen. Isn't the native resolution 1024x768 ? The screen provided EDID info seems to be wrong anyway as it started up in the wrong resolution, so on my 12.1" screen I did...
View Article